VW Touran manuals

Volkswagen Touran Owners Manual: Sealing and inflating tyres

First read and observe the introductory information and safety warnings 

Sealing a tyre

  • Unscrew the cap from the tyre valve.
  • Use the valve insert extractor   to screw the valve insert out of the tyre valve. Place the insert on a clean surface.
  • Shake the tyre filler bottle   vigorously up and down several times.
  • Screw the filler hose   tightly onto the tyre filler bottle in a clockwise direction. The plastic foil on the plug is pierced automatically.
  • Remove the plug from the filler hose   and place the open end fully on the tyre valve.
  • Hold the bottle upside down and inject the entire contents of the filler bottle into the tyre.
  • Remove the empty tyre filler bottle from the valve.
  • Use the valve insert extractor   to screw the valve insert back onto the tyre valve.

Inflating the tyre

  • Screw the tyre filler hose   of the air compressor tightly onto the tyre valve.
  • Check that the bleed screw   is closed.
  • Start the engine and let it run.
  • Insert the plug   into one of the vehicle's 12-volt sockets   .
  • Use the ON/OFF switch   to switch on the air compressor.
  • Run the compressor until the tyre pressure has reached 2.0 – 2.5 bar (29 – 36 psi / 200 – 250 kPa)  . The maximum running time is 8 minutes  .
  • Switch off the air compressor.
  • If a pressure level of 2.0 – 2.5 bar (29 – 36 psi / 200 – 250 kPa) cannot be achieved, unscrew the tyre filler hose from the tyre valve.
  • Drive (or reverse) the vehicle approx. 10 metres so that the sealing compound is more evenly distributed in the tyre.
  • Screw the tyre filler hose for the air compressor firmly back onto the tyre valve and inflate the tyre again.
  • If the required pressure still cannot be reached, the tyre is too badly damaged. The tyre cannot be sealed with the breakdown set. Do not drive on. Seek expert assistance  .
  • Disconnect the air compressor and unscrew the tyre filler hose from the tyre valve.
  • Drive the vehicle no faster than 80 km/h (50 mph) once a tyre pressure of 2.0 – 2.5 bar (29 – 36 psi / 200 – 250 kPa) has been reached.
  • Check the tyre pressure after driving for 10 minutes   .

WARNING

The tyre filler hose and the air compressor can get hot during pumping.
  • Protect your hands and skin from the hot components.
  • Do not place the hot tyre filler hose and the hot air compressor on any inflammable materials.
  • Before packing away, allow the device to cool down fully.
  • If the tyre will not inflate to at least 2.0 bar (29 psi / 200 kPa), the tyre is too damaged. The sealant is unable to seal the tyre. Do not drive on. Seek professional assistance.

NOTICE

Switch the air compressor off after a maximum of 8 minutes to avoid overheating. Let the air compressor cool down for a few minutes before switching it back on.
    Checklist
    The following actions must always be carried out in the given order in preparation for filling a wheel  : In the event of a flat tyre, park your vehicle on a flat and solid surface at a s ...

    Test after driving for 10 minutes
    First read and observe the introductory information and safety warnings Re-connect the tyre filler hose   and check the tyre pressure on the tyre pressure monitoring display ⑥. 1.3 bar (19 ...

    Other materials:

    Volkswagen Touran Owners Manual. Using the menus in the instrument cluster
    Fig. 12 Vehicles without multi-function steering wheel: press button в’¶ in the windscreen wiper lever to confirm the menu point and rocker switch в’· to change the menu Fig. 13 Right-hand side of the multi-function steering wheel: controls for the menus in the instrument cluster First rea ...

    Volkswagen Touran Service Manual. Wheel, Balancing with Fine Balancing Machine (Finish Balancer)
    Before beginning balancing, the following requirements must be fulfilled. The tire pressure must be OK. The tire profile must not be worn on one side. The tire profile must be at least 4 mm. ...

    2017-2021 © Copyright www.oticasveja.site